Advantech PPC-140 Manual do Utilizador Página 160
- Página / 194
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
142
PPC-120/140 User's Manual
Programming the Watchdog Timer
To program the watchdog timer, you must write a program which writes
I/O port address 443 (hex). The output data is a time interval value. The
value range is from 01 (hex) to 3F (hex), and the related time interval is
from 1 sec. to 63 sec.
Data Time Interval
01 1 sec.
02 2 sec.
03 3 sec.
04 4 sec.
••
••
••
3F 63 sec.
After data entry, your program must refresh the watchdog timer by
rewriting the I/O port 443 (hex) while simultaneously setting it. When you
want to disable the watchdog timer, your program should read I/O port
443 (hex).
- PPC-120/140 1
- Copyright Notice 2
- FCC Class B 3
- Packing List 4
- Safety Instructions 6
- Wichtige Sicherheishinweise 7
- Contents 8
- Appendices 13
- General Information 19
- 1.1 Introduction 20
- 1.2 How to Use This Manual 22
- 1.3 Specifications 24
- PCI SVGA/flat panel interface 25
- Audio function 25
- PCI bus Ethernet interface 26
- Touchscreen (optional) 26
- Optional modules 27
- Environment 27
- 1.4 Dimensions 28
- System Setup 29
- Infrared 30
- Fig. 2-2 31
- Main power switch 33
- AC inlet 33
- 2.3 Installation Procedures 34
- 2.3.3 Switching on the power 35
- 2.6 Installing the Drivers 37
- Using the Panel PC 39
- 3.1 Introduction 40
- 3.2 Floppy Drive 40
- 3.3 CD-ROM Drive 41
- 3.4 PCMCIA 42
- Chapter 3 43
- 3.5 PS/2 Mouse and Keyboard 45
- 3.6 PCI/ISA Bus Expansion 45
- 3.7 Parallel Port 47
- 3.8 Serial COM Ports 47
- 3.9 VGA Port 48
- 3.10 Game Port 48
- 3.11 USB Ports 48
- 3.12 Audio Interface 49
- 3.13 Ethernet 49
- 3.15 Infrared Module 50
- 3.16 Touchscreen (Optional) 50
- Hardware Installation 51
- Upgrading 52
- Metal plate 55
- 2.5" HDD 55
- DIMM socket 58
- 3.5" floppy drive 59
- Jumper Settings and 61
- Connectors 61
- 5.1 Jumpers and Connectors 62
- 5.1.2 Jumpers 63
- 5.1.3 Locating jumpers 64
- 5.1.4 Connectors 65
- 5.1.5 Locating connectors 66
- PCI clock 69
- * CPUCLK/2 69
- P55C P54C 72
- 3.5x 1.5x 72
- 2.5x 2.5x 72
- * default setting 74
- 5.2.6 Reset system (JP16) 75
- 5.3 COM-port Interface 76
- 5.4 VGA Interface 78
- 5.4.2 Panel type select (JP9) 79
- * System reset IRQ11 81
- PCI Bus Ethernet 83
- Interface 83
- 6.1 Introduction 84
- 6.3 Further Information 90
- PCI SVGA Setup 91
- 7.1 Introduction 92
- D:\VGA\Win31\Setup.exe 94
- ChipsCPL 95
- D:\VGA\Win95\ 96
- D:\VGA\NT40\ 100
- Chapter 7 PCI SVGA Setup 101
- 7.2.4 Installation for OS/2 102
- 7.3 Further Information 104
- 8.1 Introduction 106
- Chapter 8 Audio 107
- D:\Audio\win31\setup.exe 109
- D:\Audio\win95 111
- Award BIOS Setup 115
- 9.1 Award BIOS Setup 116
- 9.2 CMOS Setup Utility 116
- 9.3 Standard CMOS Setup 117
- 9.4 BIOS Features Setup 119
- Chapter 9 Award BIOS Setup 121
- 9.5 Chipset Features Setup 122
- 9.6 Power Management Setup 123
- HDD Ports Activity 126
- VGA Activity 126
- IRQ# Activity 126
- Resources Controlled By 127
- 9.8 Load BIOS Defaults 129
- 9.9 Load Setup Defaults 129
- 9.10 Integrated Peripherals 130
- IDE Burst Mode 131
- IDE HDD Block Mode 131
- Onboard FDD Controller 131
- 9.11 Password Setting 133
- 9.12 IDE HDD Auto Detection 134
- 9.13 Save and Exit Setup 135
- 9.14 Exit Without Saving 135
- Touchscreen 137
- 10.1 Introduction 138
- Chapter 10 Touchscreen 139
- BEFORE YOU BEGIN 152
- STEP 2 - COPY THE SOFTWARE 153
- STEP 3 - MODIFY CONFIG.SYS 154
- No Mouse 155
- Disabling the COM Drivers 155
- LCD Specifications and 157
- Selection Settings 157
- PPC-140T PPC-140S PPC-120T 158
- Programming the 159
- Watchdog Timer 159
- Full Disassembly 163
- Procedures 163
- PPC-120/140 User’s Manual 164
- Pin Assignments 171
- IR Connector (J1) 172
- Appendix D Pin Assignments 173
- Internal COM4 Connector (J4) 174
- Pin Signal 175
- Sandisk SSD Connector (J6) 176
- # Low active 177
- Floppy Drive Connector (J8) 178
- CD-ROM Connector (J9) 179
- CPU Fan Power Connector (J10) 179
- Fan Power Connector (J12) 185
- AT Power Connector (J13) 185
- Mounting Instructions 189
- E.1 Introduction 190
- E.2 Panel Mounting 190
- Figure E-2: Panel mounting 191
- Fixation wedge 191
- Plastic cap 191
- Rubber pad 191
- E.3 Desktop Stand Mounting 192
- E.4 Swingarm Stand Mounting 194
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.131 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais