Advantech EDG-4508R+ Manual do Utilizador descarregar pdf (Página 30)

EDG-4508(R)+/4516(R)+ User Manual 24

3.2 EDG Modules Connected Devices Group

This EDG II configuration utility will allow you to add a device via spec-

ifies the IP address. You can click ‘New’ button to add a device. And then

the EDG device will be shown on the ‘Connected Devices’ of the utility.

From here you can easily configure various parameters.

Note The EDG II configuration utility only can search

devices on the same IP domain. If you want to con-

nect the devices on another domain, you might use

this function and add the devices by yourself.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 107 108

EDG-4508+ 1
EDG-4508R+ 1
EDG-4516+ 1
EDG-4516R+ 1
User Manual 1
Contents 5
Overview 7
Chapter 1 Overview 8
3 Chapter 1 9
Getting Started 11
Chapter 2 Getting Started 12
2.1.1 Virtual COM Port Mode 13
2.1.2 Data Mode 13
2.1.3 Control Mode 13
2.2 Panel Layout 14
2.3 Connecting Hardware 15
2.3.3 Power Supply Connection 16
2.3.4 DI/O Connection 16
2.3.5 Serial Port Connection 17
2.3.6 Console Port Connection 17
2.3.7 Ordering Information 17
2.4 Installation 18
13 Chapter 2 19
15 Chapter 2 21
17 Chapter 2 23
Configuration 25
Chapter 3 Configuration 26
21 Chapter 3 27
23 Chapter 3 29
25 Chapter 3 31
3.2.1 Deleting Devices 32
27 Chapter 3 33
29 Chapter 3 35
3.4 Locating the Module 37
1. Click the “Locate” button 38
3. Click the “Stop” 38
33 Chapter 3 39
35 Chapter 3 41
3.6 Port Configuration 42
37 Chapter 3 43
Flow Control 44
Baud Rate 45
Data Bits 46
Stop Bits 46
3.6.1 Virtual COM mode 47
3.6.2 Data Mode 48
Protocol 49
3.6.3 Control Mode 51
3.7.1 Device Status 55
3.7.2 Event setting 56
3.8 UDP Testing Utility 57
53 Chapter 3 59
3.9 Updating EDG Firmware 61
Port Mapping Utility 63
4.1 Overview 64
59 Chapter 4 65
61 Chapter 4 67
4.3.1 Self Test Function 68
63 Chapter 4 69
4.3.2 Save the Configuration 71
Web-Based 73
5.1 Overview 74
5.2 Access Web Page 74
69 Chapter 5 75
5.3 Network Configuration 76
5.4 Port Configuration 77
5.4.2 Control Mode 78
5.4.3 Port UART setting 78
5.5 DI/O Event Configuration 79
5.6 Change Password 79
5.7 Reset Configuration 80
Console Configuration 81
6.1 Overview 82
Step 3. Selecting a COM Port 83
Step 4. COM Port Setting 83
6.3 Command List 85
81 Chapter 6 87
83 Chapter 6 89
85 Chapter 6 91
87 Chapter 6 93
89 Chapter 6 95
Event and DI/O 97
Monitoring 97
7.2.1 Polling Monitoring 98
7.2.2 Event Monitoring 99
7.3 Programming I/O 101
97 Chapter 7 103
Pin Assignments 105
Appendix A Pin Assignments 106
A.2.1 1. RS-422 107
A.2.2 2. RS-485 107

Comentários a estes Manuais

Sem comentários

Advantech EDG-4508R+ Manual do Utilizador Página 30

Comentários a estes Manuais

Manuais e produtos relacionados com Gateways/controladores Advantech EDG-4508R+