Advantech MMP3-21 Manual do Utilizador Página 49
- Página / 112
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Advantech SOM-Express Design Guide
Chapter 5 Carrier Board Design Guidelines 49
usually allows determining the correct trace width and spacing to achieve this
impedance, after the PCB stack-up configuration is known.
As per usual differential pair routing practices, the two traces of each USB pair
should be matched in length and kept at uniform spacing. Sharp corners should be
avoided. At the SOM-Express module and connector ends of the routes, loop areas
should be minimized. USB data pairs should be routed as far from other signals as
possible.
SOM-Express
USB[0]
USB Connector
USB[0]-
USB[3]
USB[3]-
Recommended
Not Recommended
Route to Minimum
Figure 5-8 USB Layout Guidelines
5.2.3.2 Overcurrent Protection
Overcurrent protection on external USB power lines is required to prevent faults in
external USB devices or cables from causing hardware damage and/or crashing the
system. The USBOC# signal is used to signal overcurrent conditions to the system
hardware and software. Note that overcurrent protection typically allows relatively
high currents to flow for brief periods before the current is limited or interrupted. The
system power supply must be able to provide these high currents while maintaining
output regulation, or else the SOM-Express module or other system components
may malfunction.
In case the simple resetable fuse (like shown on the reference schematic) does not
switch off fast enough, overcurrent caused by an external USB device may impact
the carrier boards internal power supply. In this case we recommend using active
protection circuits available from various vendors. These devices may be used for
per port protection of the USB power lines and allow direct connection to the
USB_X_X_OC# signal.
NOTE: This circuit does not get implemented on SOM-Express. Please implement it
on the carrier board.
USBVFBO
F1
L38
1A
USBOC#
C72
0.01u
R49
470K
11P300S
USBVCC
R50
560K
C73
100
C74
0.1u
VCC
Figure 5-9 Overcurrent Circuit
- Advantech 1
- Notices 2
- Revision History 2
- Table of Contents 3
- 4 Table of Contents 4
- Table of Contents 5 5
- 6 Table of Contents 6
- Table of Contents 7 7
- 8 Table of Contents 8
- Chapter 1 Introduction 9
- 1.2 Referenced Documents 10
- 2.1 Overview 11
- 2.2 Specifications 13
- 2.2.1 SOM-5780 14
- 2.2.2 SOM-5782 16
- 2.2.3 SOM-DB5700 18
- 2.3 System Resources 19
- 2.3.1 SOM-5780 Resources 19
- 2.3.2 SOM-5782 Resources 22
- 2.4 PCI Routing 25
- 2.5 DC Specifications 25
- 2.5.1 Interface I/O Voltage 25
- 2.5.1.3 Audio 27
- 2.5.1.4 VGA 27
- 2.5.1.5 LCD 28
- 2.5.1.6 IDE 28
- 2.5.1.7 Ethernet 28
- 2.5.1.8 TV-Out Bus 28
- 2.5.1.9 IrDA 28
- 2.6 AC Specification 29
- 2.6.1 PCI-Bus AC Spec 29
- 2.6.3 Audio AC Spec 29
- 2.6.4 VGA AC Spec 29
- 2.6.5 IDE AC Spec 30
- 2.6.6 I2C AC Spec 30
- 2.6.7 SMBus AC Spec 30
- Chapter 3 Pin Assignments 31
- 3.1 Row A 32
- 3.2 Row B 33
- 3.3 Row C 34
- 3.4 Row D 35
- 4.1 Nominal Board Stack-Up 36
- Thickness 37
- 4.3 Alternate Stack Ups 39
- 5.1 PCI-Bus 40
- 5.1.1 Signal Description 40
- 5.1.2 Design Guidelines 41
- Vtest 0.4 Vcc 1.5 V 42
- Tskew 2 (max) 2 (max) ns 42
- 5.1.3 Layout Guidelines 44
- Carrier 45
- 5.1.4 Application Notes 46
- 5.2.1 Signal Description 47
- 5.2.2 Design Guidelines 47
- 5.2.3 Layout Guideline 48
- SOM-Express 49
- USB Connector 49
- 5.2.3.4 Stubs 50
- 5.3.1 Signal Description 51
- 5.3.2 Design Guidelines 51
- 5.3.2.3 Azalia: 52
- Analog Ground 53
- 5.3.3 Layout Guidelines 54
- ± 15% 54
- 5.4 VGA 56
- 5.4.1 Signal Description 56
- 5.4.2 Design Guidelines 57
- 5.4.3 Layout Guideline 57
- VGA Connector 58
- 5.5 LVDS 59
- 5.5.1 Signal Description 59
- 5.5.2 Design Guideline 59
- 5.5.3 Layout Requirements 60
- 5.6 Primary IDE0 61
- 5.6.1 Signal Description 61
- 5.6.2 Design Guidelines 61
- IDE bus IDE cable 62
- Total Max 62
- Length 13 inches 62
- Carrier Board 62
- 5.6.3 Layout Guidelines 63
- 5.7 Ethernet 64
- 5.7.1 Signal Descriptions 64
- 5.7.2 Design Guidelines 64
- LAN Connector 65
- 5.7.3 Layout Guidelines 66
- 5.7.3.2 Transformer 67
- 5.7.3.3 Critical Dimensions 68
- 5.8 TV-Out 70
- 5.8.1 Signal Descriptions 70
- 5.8.2 Design Guidelines 70
- TV DAC Filter 71
- 5.9 Miscellaneous 72
- Carrier board 74
- 5.10 PCI Express Bus 77
- 5.10.1 Signal Description 77
- Pin Signal I/O Description 77
- 5.10.3.1 Differential pairs 81
- Guidelines 82
- L1 L2 L3 Capacitor Value 83
- L1 L2 Capacitor Value 83
- 5.11 Serial ATA 84
- 5.11.1 Signal Description 84
- 5.11.2 Design Guidelines 84
- 5.11.3 Layout Guidelines 85
- 5.12 LPC 87
- 5.12.1 Signal Description 87
- 5.12.2 Design Guidelines 87
- 5.12.3 Layout Guidelines 87
- 5.12.4 Application Notes 88
- 5.12.4.3 LPT/Floppy 89
- 5.12.4.4 EMI Considerations 89
- Parallel Port 90
- 6.2 Design Guidelines 95
- 8.1 Material of Heatsink 101
- 8.4 Grounding Issues 102
- 8.8.1 Vendor List 106
- 8.8.2 Heat-Spreader 106
- 8.8.3 Heat-Sink 107
- 8.8.4 Thermal Pad 108
- M2.5*6 5 109
- M2.5*16 5 109
- Quantity 109
- 8.8.6 Fan 110
Manuais e produtos relacionados com Barebones PC/estação de trabalho Advantech MMP3-21
(30 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais